Consoles and Dressers

Custom TV Units for Hotel Guest Rooms: Sizes, Cable Routing and Wall Fixing Options

Good hotel TV unit design starts with the screen, the cables and the wall, not the finish. This guide walks through the build details to settle before you discuss style or request a quotation.

Hotel TV unit design is easiest to get right when you work from the inside out: the screen, the equipment behind it, the cables and the wall that carries the weight. Style and finish matter, but they are the last decisions, not the first. This guide covers the practical build details of a custom TV unit for a hotel room so that your drawings, and the quotation that follows, are complete from the start.

We make custom units to project drawings for hotels worldwide, in single-project and bulk orders. The points below are the ones we find most often decide whether a unit installs smoothly across hundreds of rooms.

Start with the screen, not the furniture

Every dimension of the unit follows from the television. Before drawing anything, confirm the exact model or at least the maximum size you will specify, because panel dimensions, stand feet, bezel depth and bracket type vary between brands.

Collect the following from the TV data sheet:

  • Overall width, height and depth, with and without the stand.
  • Weight of the screen.
  • VESA mounting pattern, if a bracket will be used.
  • Position of the input panel and power inlet (rear, side or downward facing).
  • Any ventilation clearance the manufacturer requires.

If the hotel brand may change TV suppliers during the project, design the unit around the largest likely screen and a standard VESA pattern. A little spare room is far cheaper than redrawing a unit for 200 rooms.

Sizing the unit around the screen

As a planning rule, the unit should be wider than the screen so it looks deliberate rather than cramped. The exact margins depend on the design, but the logic is consistent.

Width and depth

Allow a visible margin on each side of the screen if the TV sits on the unit, and a clear gap if it is wall mounted above a console. Depth is driven by what sits inside or on top: a slim console for a wall-mounted screen can be shallow, while a unit that houses a set-top box, a minibar or a luggage shelf needs more depth. Always measure the deepest piece of equipment and add space for connectors and cables, which need room to bend.

Height

Height is a viewing question as much as a furniture one. The centre of the screen should sit roughly at seated eye level from the bed or sofa, which is why a TV mounted too high is a common complaint in hotel rooms. Decide the viewing position first, then work out the height of the base unit and the bracket position. If the room has both a bed and a seating area, check both viewing points on the plan.

A simple planning table

Item to confirmWhy it mattersWho provides it
Screen model and sizeSets unit width, cut-outs and bracketOwner or FF&E manager
Mounting methodDecides structure and wall fixingDesigner with manufacturer
Equipment listDetermines internal compartments and ventilationTechnology consultant
Wall constructionDetermines anchors and backingContractor or architect
Socket and data positionsDefines cable cut-outsMEP engineer

Cable routing: plan it before the carcass

Cable routing is where good-looking units fail in practice. If cables are an afterthought, installers drill holes on site, finishes get damaged and loose leads end up visible behind the screen.

What to route

A typical guest room screen needs a power lead, an HDMI or casting connection, a network cable or Wi-Fi module and sometimes an antenna or set-top box lead. Add the minibar or lamp power if the unit combines functions. List every cable and its entry point before the drawings are finalised.

Cut-outs and channels

On the shop drawings, mark cut-outs for cables with their position, size and edge treatment. Edges of cable holes should be sealed or fitted with grommets so that moisture and abrasion do not damage the board. Where cables travel inside the unit, a vertical channel or a removable back panel keeps them tidy and lets technicians reach them later.

Service access

Plan how a technician replaces a faulty box or lead without removing the unit from the wall. A removable panel, a hinged section or a small access hatch is a modest addition at the design stage and saves considerable time in service. Fixing everything permanently behind a closed panel looks neat on day one and becomes a problem in year two.

Ventilation and heat

If the unit encloses a set-top box, a media player or a power supply, it needs airflow. Electronic equipment in a closed cabinet can overheat and fail early. Simple measures help: ventilation slots or a rear gap, spacing between devices and an open back where the design allows. Always follow the equipment manufacturer's clearance requirements.

Wall fixing options

The unit is only as secure as the wall behind it. The wall type determines the fixing method, so the contractor's wall build-up should be part of the specification, not a surprise on installation day.

  • Concrete or masonry: suitable for mechanical anchors chosen for the load and substrate.
  • Drywall or partition: needs reinforcement such as timber or metal backing behind the board at fixing points. Plain plasterboard anchors are not appropriate for heavy screens or units.
  • Panelled or clad walls: decide whether the unit fixes through the panelling to the structure behind, or whether the panelling is part of the unit itself.

Ask the manufacturer to show fixing points, bracket positions and recommended anchors on the shop drawing, and have the structural or fit-out contractor confirm they suit the actual wall. Weight limits for the screen, bracket and unit should be checked against the manufacturer's data rather than assumed.

Floating, floor-standing or built-in

A floating unit looks light and leaves floor space clear for cleaning, but it relies entirely on the wall. A floor-standing unit transfers weight to the floor and is more forgiving, though it may need anti-tip fixing if tall. A built-in wall unit gives the cleanest result and hides cables best, but it must be coordinated with the construction schedule and the room layout from the start.

Materials that suit daily hotel use

Once the technical points are settled, choose materials for wear. HPL and quality veneers tolerate cleaning and scuffs well, and solid wood or ABS edging protects edges. Commercial-grade hinges and runners matter if the unit has doors or drawers. If the destination market has fire requirements, confirm the need for fire-retardant (FR) boards or finishes early, since they can affect cost and lead time.

Approving the design before bulk production

For a project with many rooms, a sample or mock-up room is the safest step. It lets you test the screen height, cable routing, access panels and fixing in a real setting. Adjustments at this stage are small; the same changes after production starts are not. Agree the approved drawing, finish sample and hardware list in writing, so that every unit in the order is identical.

Planning for bulk orders and worldwide delivery

Hotels often need dozens or hundreds of identical units, and manufacturing them in our own Istanbul factory allows consistent dimensions and finishes across the whole batch. For international projects, agree the shipping terms (such as FOB or DAP), packing method and delivery sequence early. Lead time and cost depend on quantity, materials, finish and the approval process, so we prefer to quote against your drawings rather than offer generic figures.

Checklist before you request a quotation

  1. Screen model and maximum size, with VESA pattern.
  2. List of equipment to be housed in or behind the unit.
  3. Viewing positions and target screen height.
  4. Socket, data and cable entry positions.
  5. Wall construction at each room type.
  6. Finish, edge and hardware preferences, plus any FR requirements.
  7. Quantity per room type and destination country.

Next step

If you are planning a new hotel or a renovation, send us your drawings or room schedule. We will review the TV unit details with you and come back with material suggestions, an estimated lead time and shipping options for your project.

Sıkça Sorulan Sorular

What information do you need to quote a custom TV unit for a hotel room?

Send the screen model or maximum size, equipment to be housed, room drawings, socket positions, wall construction, finish preferences and quantities per room type. Even a rough room schedule helps. We then review it and come back with questions, material suggestions and an estimate based on your project.

How do you hide cables in a hotel TV unit?

Cables are routed through marked cut-outs with grommets into a vertical channel or behind a removable back panel. The positions are fixed on the shop drawing before production, so nothing needs drilling on site. A service panel lets technicians reach connections later.

Can a hotel TV unit be fixed to a drywall partition?

Yes, but only with proper reinforcement such as timber or metal backing behind the boards at the fixing points. Standard plasterboard anchors are not suitable for heavy screens. Your contractor should confirm the wall build-up so the fixing method can be specified correctly.

Do you make TV units in bulk for hotel projects?

Yes. We produce custom units to project drawings in our Istanbul factory, from single rooms to large batches, and ship worldwide. Quantity, finish and approvals affect cost and timing, so we confirm these against your drawings and an approved sample.

Is a mock-up room necessary for TV units?

It is strongly recommended for larger orders. A mock-up lets you check screen height, cable routing, access panels and fixing in a real room. Corrections are inexpensive at that stage and costly once bulk production has begun.

Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.

Related products

All Console Table Models

Get a quote for Console Table Models

Share dimensions and quantities; we will prepare a quote for your project.