Consoles and Dressers

Vitrine Cabinet Dimensions Guide: Standard Heights, Widths and Depths for Residential and Commercial Use

A plain reference chart of typical vitrine sizes by use case, so you can start a custom or bulk order with realistic numbers. Use it as a starting point, then adjust to your space and products.

Most vitrine cabinet dimensions fall into a fairly narrow range: roughly 180-220 cm (71-87 in) tall, 60-120 cm (24-47 in) wide per section and 30-45 cm (12-18 in) deep for display use. These are common working figures, not fixed standards, because there is no single international rule for display furniture. This guide gives you a plain reference chart by use case, so you can brief a factory with realistic numbers and then request custom changes.

Why there is no single standard size

Vitrines are made by many workshops and factories, and each one builds around its own board sizes, glass sheet sizes and hardware. What buyers call a display cabinet standard size is really a set of common ranges that have proved practical for rooms, doorways and typical objects.

For you as a buyer, this is good news. Starting from a typical size keeps the design efficient, and small adjustments are usually easy to make. Large departures from the range often need new drawings, extra reinforcement or different glass.

The three dimensions that matter

Height

Height is set by ceiling height, the viewing level of the objects and how the cabinet will be delivered. A tall vitrine looks impressive, but it must pass through doors and stairwells and, in some cases, be anchored to the wall.

Width

Width decides how many shelves, doors and glass panels you need. Single sections are easier to ship and handle. Wide cabinets are often built as two or three joined modules rather than one long body.

Depth

Depth controls what you can show. A shallow cabinet suits small items, books and collectibles. A deeper one suits crockery, bottles and products that need to be seen from the front at an angle.

Quick reference chart by use case

The table below shows typical starting ranges. Treat them as planning figures to discuss with the factory, not as limits.

Use caseHeightWidth (per section)Depth
Living room vitrine (home)180-210 cm (71-83 in)80-120 cm (31-47 in)35-45 cm (14-18 in)
Dining room crockery vitrine190-220 cm (75-87 in)90-130 cm (35-51 in)40-50 cm (16-20 in)
Narrow or corner vitrine170-200 cm (67-79 in)45-70 cm (18-28 in)30-40 cm (12-16 in)
Hotel lobby display180-230 cm (71-91 in)80-150 cm (31-59 in)35-50 cm (14-20 in)
Restaurant or bar display150-210 cm (59-83 in)80-120 cm (31-47 in)30-45 cm (12-18 in)
Retail shop or boutique120-220 cm (47-87 in)60-120 cm (24-47 in)30-50 cm (12-20 in)
Low counter-style vitrine90-110 cm (35-43 in)90-180 cm (35-71 in)40-60 cm (16-24 in)

Residential vitrines: what to expect

In homes, vitrines usually stand in living rooms and dining rooms, so proportions follow the rest of the furniture. A typical floor-standing model sits below the ceiling with a small gap, which makes it easier to install and move.

  • Living room: mixed storage is common, with glass doors on top and solid doors or drawers below.
  • Dining room: deeper shelves hold plates, glasses and serving pieces, so depth is often slightly greater.
  • Corner or narrow spaces: reduced width and depth help the cabinet fit without blocking circulation.

Commercial vitrines: hotels, restaurants and shops

Commercial use changes the brief. Cabinets must work for guests or customers, tolerate daily cleaning and often need locks, lighting and stronger shelving.

Hotel lobbies and public areas

Lobby vitrines are often taller and wider for visual impact. They may show local crafts, awards, branded items or gift shop products. Allow space for lighting drivers and cable routing, because these can affect internal depth and the back panel design.

Restaurants and bars

Here, vitrines display wine, pastry, glassware or trophies. Heights are often lower so the display sits within sight lines, and depth is chosen around bottle or tray sizes. Think about staff access from the back or side if the unit is also used for service.

Retail corners and boutiques

Shop vitrines vary the most. Counter-height cases suit jewellery and small goods, while tall wall cabinets suit larger stock. Shelf spacing is usually set by the product, so measure your biggest item first.

Shelf spacing and internal clearances

Outside measurements are only half the story. The usable internal space depends on panel thickness, glass thickness and the space needed for hinges and lighting.

  • Small objects: shelf gaps of around 20-30 cm (8-12 in) are common.
  • Books, bottles and mid-size items: 30-40 cm (12-16 in) is a practical starting range.
  • Large items: measure the object, then add a few centimetres of clearance above and in front.

Adjustable shelves give you room to change displays later, which is helpful in shops and hotels where stock or décor changes.

Practical limits to check before fixing a size

Before you finalise any figure, check these points:

  • Delivery route: doors, lifts and stairwells must be wider and taller than the packed cabinet.
  • Glass size: very large panels are heavier, harder to ship and more costly to replace.
  • Shelf span: wide shelves may need thicker glass or a centre support to avoid sagging.
  • Wall fixing: tall units may need anchoring, and wall type affects the method.
  • Floor and skirting: allow for skirting boards, uneven floors and adjustable feet.

How to move from a standard size to a custom one

A good approach is to pick the closest line in the chart, then list only the changes you need. This keeps your request clear and makes the first quotation faster.

  1. Choose the use case and the typical size range.
  2. Measure the available space and the largest object to be displayed.
  3. Decide on glass type, lighting and locks, since they influence internal dimensions.
  4. Send a sketch, photo or drawing with your changes marked.
  5. Review the shop drawing and confirm sizes before production.

Notes for bulk and worldwide orders

If you are ordering many pieces for a hotel group, a retail chain or a distribution business, fewer sizes usually make production and shipping simpler. A small family of two or three widths, built on the same height and depth, is often easier to manage than many unique dimensions.

Also think about how the cabinets will be packed. Overall size affects how many pieces fit in a container and whether modular or assembled formats make more sense. Your destination market may also influence the choice, since local room sizes and building types differ.

Common sizing mistakes to avoid

  • Measuring the room but not the delivery route.
  • Ignoring the thickness of the back panel, glass and lighting when counting internal space.
  • Choosing shelf spacing before knowing the product dimensions.
  • Specifying very wide glass shelves without checking load and span.
  • Mixing metric and imperial figures in one drawing.

Next step

If you are planning a vitrine for a home, hotel, restaurant or shop, send us your room dimensions, a sketch or reference photos and the quantity you need. We will suggest suitable vitrine dimensions, point out any practical limits and prepare a quotation for your custom or bulk order.

Sıkça Sorulan Sorular

What are the standard vitrine cabinet dimensions?

There is no single international standard, but many vitrines are 180-220 cm (71-87 in) tall, 60-120 cm (24-47 in) wide per section and 30-45 cm (12-18 in) deep. Commercial and retail pieces vary more, so treat these figures as a starting point for discussion.

How deep should a display cabinet be?

For small items and collectibles, 30-35 cm (12-14 in) is common. For crockery, bottles or larger products, 40-50 cm (16-20 in) gives more room. Check your largest object first, then allow clearance for lighting and glass.

What height is best for a hotel lobby vitrine?

Many lobby vitrines are 180-230 cm (71-91 in) tall, but the right height depends on ceiling height, viewing level and wall fixing. Also confirm that the packed cabinet can pass through doors and lifts on site.

Can I change the size of a standard vitrine model?

Usually yes. Small changes to width, height or shelf spacing are common and easy to draw. Bigger changes may affect glass thickness, shelf span or reinforcement, so the factory will review them and confirm with a shop drawing.

What should I send to get a quotation for vitrine sizes?

Send your room or wall dimensions, a sketch or reference photos, the objects to be displayed, preferred materials and the quantity. Mention any glass, lighting or lock requirements, and your delivery country, so the quotation can be accurate.

Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.

Related products

All Console Table Models

Get a quote for Console Table Models

Share dimensions and quantities; we will prepare a quote for your project.