Sample Photo Approval Checklist for Vitrines: Eight Angles to Request Before Production
A practical shot list for approving a vitrine sample remotely. Eight photo angles help you check glass, hinges, lighting and interior finish before bulk production begins.
A vitrine sample approval checklist gives you a repeatable way to judge a display cabinet from photos and short videos, without travelling to the factory. The most useful approach is to request a fixed set of eight angles that cover glass, hardware and interior details, because that is where problems in bulk orders usually start. This guide sets out the shots to ask for, what to look for in each, and how to record your decision.
Why a defined shot list matters
Factories usually send one or two attractive front photos of a sample. These show the overall look, but they hide glass edges, hinge alignment, shelf supports and the inside of the back panel. A fixed shot list removes guesswork and makes your approval easier to document.
It also helps when several people review the sample, such as the designer, the buyer and the project manager. Everyone looks at the same images and comments on the same points. If a detail changes later, you have a clear record of what was approved.
Before you start: set up the review
- Agree on the approved drawing or specification the sample must match.
- Ask for photos in original resolution, not compressed chat images.
- Request a tape measure or ruler in at least some shots for scale.
- Ask for natural or neutral daylight where possible, with no strong colour cast.
The eight angles to request
1. Straight front view, doors closed
Shoot this from the centre at mid-height, with the camera parallel to the cabinet. Check overall proportions, door gaps, glass reflections and whether the finish looks even. Compare the outline to your drawing, including plinth height and any cornice or top detail.
2. Front view, doors open
This shows the interior layout in one image. Check shelf positions, number of shelves, back panel material and how the lighting sits. Look for visible screw heads, uneven shelf spacing or gaps between the back panel and the sides.
3. Glass edge close-up
Ask for a macro shot of an exposed glass edge on a door and on a shelf. You want to see whether the edges are polished or seamed, whether corners are slightly rounded, and whether there are chips or flare marks. For tempered glass, also ask for a photo of the etched or printed marking, if your market expects one.
4. Hinge and door-edge detail
Take this at the top and bottom hinge positions, with the door closed and then open to about 90 degrees. Check that the hinge type matches the specification, that glass clamps or cups are seated flat, and that the door sits level with its neighbour. Also ask for a short video of the door opening and closing to show smoothness and any rubbing.
5. Shelf support and shelf edge
Photograph a shelf in place, then one with the shelf removed to show the support pins or channels. This tells you how the shelf is held and whether pin holes are drilled cleanly and in line. If glass shelves are used, check for protective pads under the glass and a stable seat on each support.
6. Interior corners and back panel
A raking shot along the inside of the cabinet reveals joint quality, edge banding at the interior, and any glue residue. On mirror-back or backlit models, look at how the panel is fixed and whether there are visible gaps at the edges. This is also where finish consistency between inside and outside shows up.
7. Lighting and cable detail, if included
If the vitrine has LED lighting, request one photo with the lights on in a dim room and one with them off showing the strip, channel and driver position. Check for hot spots, visible dots from the diodes and exposed wiring. Ask where the driver sits and whether it can be reached for service.
8. Base, back and underside
The last angle covers the parts that customers rarely see but installers and cleaners do. Photograph the plinth or feet, the back of the cabinet, any wall fixing brackets and the underside. Check levelling feet, hanging rails, cable outlets and whether the back is finished or left raw according to your specification.
A quick comparison table
| Angle | Main focus | Common issue to spot |
|---|---|---|
| 1. Front, closed | Proportions, gaps, finish | Uneven door gaps |
| 2. Front, open | Interior layout | Wrong shelf count or spacing |
| 3. Glass edge | Edge quality | Chips, rough edges |
| 4. Hinges | Hardware and alignment | Door rubbing or sagging |
| 5. Shelf supports | Load path | Loose or misaligned pins |
| 6. Interior corners | Joinery and banding | Glue marks, gaps |
| 7. Lighting | Light quality, driver access | Visible diodes, hot spots |
| 8. Base and back | Fixings and finishing | Missing levelling or wall brackets |
How to review the photos
Open each image at full size and compare it with the drawing or specification, not with your memory of the design. Mark any deviation directly on the photo, using simple arrows and short notes. Send these comments in one consolidated message, so the factory can answer every point at once.
Separate your comments into three groups: must fix before production, acceptable as is, and questions that need clarification. This keeps the discussion clear and prevents small cosmetic points from delaying the whole order.
Add short videos to the photo set
Photos cannot show movement. Ask for two or three short clips: a door opening and closing, a hand pressing lightly on the shelf edge, and a slow pan around the cabinet. These clips reveal squeaks, wobble and visible play in the hinge that still images hide.
Record the approval properly
Once you are satisfied, confirm approval in writing and refer to the sample by name or number. List any agreed changes, such as a different hinge, an adjusted shelf height or a revised finish tone. Ask the factory to keep the physical sample, or to send it to you, so that it can serve as the reference for the bulk batch.
For larger orders, it is sensible to note tolerances you accept, such as door gap range or slight variation in wood grain. This protects both sides and shortens any discussion at inspection.
When photos are not enough
Photos work well for construction details and finish, but some points need a physical sample or a live video call. Colour matching on lacquered or stained surfaces and the feel of a veneer are hard to judge on a screen. If the colour is critical, request a small finish sample by courier as well.
A live call can also be useful for checking the sample against a measuring tape, or for asking the factory to move the camera to an angle you want to see again.
Conclusion
A clear vitrine sample approval checklist turns remote sample review into a structured process. Eight angles, a few short videos and a written approval are usually enough to catch most issues before production begins. If you are planning a custom vitrine order for a hotel, store or wholesale programme, send us your drawings or reference photos and we will prepare a sample with a photo set based on this checklist, together with a quotation for your quantities.
Sıkça Sorulan Sorular
How many photos should I ask for when approving a vitrine sample?
At least eight, one for each key angle: front closed, front open, glass edge, hinges, shelf supports, interior corners, lighting and the base or back. Add two or three short videos of doors and shelves. This gives enough evidence to approve construction details without visiting the factory.
Can I approve a vitrine sample from photos alone?
For construction and layout, yes, if the photos follow a defined shot list. For colour, veneer feel or glass tint, a physical finish sample or a live video call is safer, because screens often distort colour.
What glass details should I check in sample photos?
Look closely at edge finish, corner rounding, chips, and any tempered glass marking. Also check how the glass is seated in hinges or clamps and whether shelf glass rests on protective pads. Request a macro close-up of an exposed edge.
Why are hinge photos important in a pre-production approval?
Hinges control door alignment and long-term wear. Photos at the top and bottom hinge, plus a short opening video, show whether the hardware matches the specification and whether doors sit level without rubbing.
What should I do after approving the sample?
Confirm approval in writing, reference the sample number and list any agreed changes. Ask the factory to keep the approved sample as the reference for the bulk batch, so later inspections compare against the same standard.
Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.





