Consoles and Dressers

How to Compare Console Table Quotes from Different Countries: A Side-by-Side Method

Quotes from different countries rarely describe the same product. This guide shows how to build a normalised comparison sheet so materials, Incoterms and finish assumptions line up before you look at price.

If you need to compare console table quotes from suppliers in several countries, the unit price is the least reliable place to start. One offer may assume solid oak and a satin lacquer delivered to your door, while another assumes veneer on MDF, a basic stain and ex-works pickup. Placing those numbers next to each other tells you very little. The method below turns every offer into a like for like specification so you compare the same thing.

Why raw quotes are not comparable

Quotes differ in at least four layers: what is being built, how well it is finished, what is included in the price and under which commercial terms it is delivered. A low figure usually means a lower assumption in one of those layers, not a more efficient supplier.

Before you read a single price, decide which layer each difference belongs to. This keeps the discussion with suppliers factual and avoids arguments about who is expensive.

Step 1: Write one master specification

Your first task is to create a single brief that every supplier prices. The more precise it is, the less room there is for private assumptions. A good master specification for a console table includes:

  • Overall dimensions in millimetres (with inches in brackets if your team uses them) and permitted tolerance.
  • Top construction: solid timber, veneered board, stone or glass, and the thickness.
  • Base and leg construction, including how legs connect to the top.
  • Timber species or veneer type, grade and grain direction.
  • Finish type, colour reference, gloss level and number of coats if relevant.
  • Hardware: drawer runners, hinges, levelling feet, wall fixings.
  • Quantity, batch structure and delivery location.
  • Fire, moisture or environmental requirements of the destination country.

If you have drawings, send them. If you only have a photo or mood board, say so, and ask each supplier to list the assumptions they made when interpreting it.

Step 2: Build the normalised comparison sheet

Create a spreadsheet with one column per supplier and one row per line below. Fill in what each quote states, and mark anything that is silent as "not stated" rather than guessing. Silence is information: it usually means the item is excluded or downgraded.

RowWhat to recordWhy it matters
Product matchDimensions, tolerance, top and base constructionConfirms the offer matches your drawing
MaterialSpecies, veneer or solid, board core, edge detailLargest driver of both price and durability
FinishSystem, colour reference, sheen, sample providedAffects wear, repairs and colour consistency
HardwareBrand or grade, soft-close, levellingShows long-term service quality
PackingMethod, crating, protection of corners and topsInfluences damage risk and freight volume
IncotermEXW, FOB, CIF or DAP and named placeDecides who pays and who carries risk
Taxes and dutiesIncluded or excludedCan change the landed cost significantly
Sample and toolingCost, timing, credit against orderOften missing from unit price
Lead timeStarting point (sample approval or deposit)Different start dates distort comparison
Payment termsDeposit, milestones, balanceAffects cash flow and negotiating position
ValidityHow long the quote holdsMaterial prices and currencies move

Step 3: Normalise materials and finishes

Material differences are where most hidden savings sit. A solid timber top, a veneered top on engineered board and a laminate-faced board can look alike in a render yet behave very differently after years of luggage and cleaning. Ask each supplier to name the exact species, the board core and the edge treatment, then adjust your sheet so that every column is described in the same terms.

Finishes need the same care. "Natural oak finish" can mean anything from a thin oil to a multi-coat protective lacquer. Ask for the finish system, the sheen level and a physical sample under the lighting you will use. If one supplier has quoted a simpler system, either request a revised quote for your specified one or note the gap so you can weigh it consciously.

Step 4: Normalise Incoterms and delivery scope

Quotes from different countries often use different Incoterms, which makes the headline prices incomparable. An EXW price excludes export clearance and freight, FOB covers delivery onto the vessel at the named port, CIF adds sea freight and insurance to the destination port, and DAP includes delivery to your named place, usually excluding import duties.

The cleanest approach is to ask every supplier to requote on one basis, for example FOB or DAP to your site. If that is not possible, add estimated freight, insurance, customs clearance and inland transport to the lower-scope offers, and label these as your own estimates. Do not treat estimates as quoted figures when you present the comparison to colleagues.

Check what sits outside the unit price

Some costs appear only as separate lines or not at all. Look for:

  • Sample and prototype charges, and whether they are credited if you order.
  • Tooling, jigs or templates for custom shapes.
  • Export crating versus standard cartons.
  • Document fees, inspection fees and labelling requirements.
  • Installation or supervision, if you need it.

Step 5: Compare timing on the same start line

Lead time claims are only meaningful when they begin from the same event. One supplier may count from deposit, another from sample approval, and a third from the date drawings are signed off. Convert every quote to the same starting point and add transit time for the chosen route.

We do not publish a fixed production time because it depends on quantity, materials, finish complexity and the approval process. Treat any supplier who gives a very short promise without asking about your drawings with some caution, and ask what the schedule assumes.

Step 6: Weigh the non-price factors

Once the sheet is normalised, price differences become genuine, and you can look at the remaining factors that a spreadsheet cannot show fully:

  • Quality of the technical drawings and how quickly questions are answered.
  • Willingness to produce a sample or mock-up before mass production.
  • Clarity on tolerances and batch consistency for repeated pieces.
  • Communication across time zones and the format of progress reports.
  • Process for handling defects after delivery.

A simple scoring approach works well: give each factor a weight that reflects your project priorities, score each supplier, and discuss the result with your team. The aim is not to produce a perfect number but to make trade-offs visible.

Common comparison mistakes

  • Comparing unit price only. Landed cost, including freight, duties and samples, is what you actually pay.
  • Accepting vague wording. Terms such as "premium wood" or "high-quality finish" should be replaced with named species and finish systems.
  • Mixing currencies without a rule. Pick a reference date and a single currency for the sheet, and note it.
  • Ignoring quote validity. A cheaper offer that expires next week may not be comparable to one valid for two months.
  • Skipping a sample. Differences in colour and finish are hard to judge from photographs.

Working with a made-to-order manufacturer

Palmiye produces custom wooden furniture to project drawings in our own factory in Istanbul and supplies hospitality projects worldwide. Because pieces are made to order, we ask for dimensions, material, finish and quantity first, then state our assumptions in the quotation so that you can place it directly on your comparison sheet. If you already have offers from other countries, you are welcome to send them with your specification and we will help you identify where the assumptions differ.

Summary

To compare console table quotes fairly, define one master specification, record every offer in a normalised sheet, align materials, finishes, Incoterms and start dates, and then weigh the non-price factors. This takes a little more time upfront, but it prevents surprises on site and gives you a defensible basis for your supplier decision.

If you would like a quotation that is easy to compare, send us your drawings, photos or room schedule and we will respond with a clearly itemised offer for your project.

Sıkça Sorulan Sorular

How do I compare console table quotes from different countries?

Write one master specification, ask each supplier to price it, and record the answers in a single sheet covering dimensions, materials, finish, hardware, packing, Incoterm, taxes, lead time and payment terms. Mark anything missing as not stated, then align the Incoterms and start dates before comparing totals.

Which Incoterm is easiest for comparing furniture quotes?

Ask every supplier to quote on the same basis. FOB is common for comparing factory prices, while DAP is easier if you want to see a delivered cost. If quotes use different terms, add your own freight and clearance estimates and label them clearly.

Why are some console table quotes much cheaper than others?

Usually the specification differs: thinner veneer, a lower-grade board core, a simpler finish, basic hardware, lighter packing or a lower Incoterm scope. Ask for named materials and finish systems so you can see exactly where the difference comes from.

Should I ask for a sample before comparing offers?

Yes, whenever possible. A sample shows real colour, finish quality and construction, which photographs and descriptions cannot. Check whether sample cost is credited against the order and how long it takes, as both vary by supplier and design.

What costs are often missing from a unit price?

Common omissions include sample and prototype charges, tooling for custom shapes, export crating, inspection or document fees, import duties and inland delivery. Ask each supplier to list included and excluded items so your comparison reflects the landed cost.

Can I send a photo or mood board to get comparable quotes?

You can, but suppliers will interpret it differently. Ask each one to list their assumptions on size, material and finish, or give them a short written specification alongside the image. Drawings produce the most consistent and comparable offers.

Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.

Related products

All Console Table Models

Get a quote for Console Table Models

Share dimensions and quantities; we will prepare a quote for your project.