Console Table Finish Samples: Choosing Between Stain Cards, Door-Size Panels and Full Mock-Ups
Stain cards, door-size panels and full mock-ups each answer a different question about colour and finish. This guide compares the three by cost, accuracy and approval confidence so you can choose the right one for your hotel order.
Choosing the right format for console table finish samples comes down to one question: how much risk are you willing to carry into mass production? A small stain card is quick and economical, a door-size panel shows far more of the real finish, and a full mock-up proves the entire piece. Each has a place, and the right choice depends on your quantity, your timeline and how critical the colour is to the design.
This guide compares the three formats side by side. It does not repeat the general approval process; it focuses on what each sample type can and cannot tell you, so you can decide before you brief the factory.
Why the sample format matters
A finish is more than a colour. It is the combination of timber or veneer, grain pattern, stain or lacquer, sheen level and surface texture. A small sample can show some of these and hide others.
When a sample is too small or too simple, approval gives a false sense of security. The first time you see the real piece may be on site, when changes are no longer practical. Matching the sample format to the risk is the most reliable way to avoid that.
Format 1: The stain card
A stain card is a small board, usually the size of a hand or a little larger, finished in one or more colour options. It is the standard first step when you are still choosing a direction, and it is the fastest and most economical format.
What a stain card shows well
- The base colour and undertone of a wood stain sample on a specific species.
- Relative differences between several colour options placed side by side.
- The basic sheen level, such as matte or satin.
What a stain card cannot show
- How the grain pattern behaves across a large surface, including cathedral figure or cathedral-free sections.
- Colour variation between boards or veneer sheets in a large order.
- How the finish looks on edges, curved parts or profiled details.
- Real hardware, joints or the interaction of different materials.
Think of a stain card as a shortlisting tool. It lets you eliminate options cheaply, but it is rarely strong enough to be the only approval document for a large hotel batch.
Format 2: The door-size panel
A door-size panel is a larger finished board, often around 300 x 600 mm (12 x 24 in) or bigger, sometimes close to the size of a real console top. It is the working format behind most finish approval panel decisions in hospitality projects.
What a door-size panel adds
- A realistic view of grain and figure across a meaningful area, so you judge the pattern and not only the tone.
- Better judgement of how light moves across the surface at different angles.
- The chance to include an edge profile, so the edge finish is visible too.
- A clearer picture of natural variation, especially if two or three panels from different boards are supplied.
Where it still falls short
A flat panel does not show construction. It cannot tell you how a finish behaves on a turned leg, a fluted surface or a tight inner corner, where spray coverage and absorption differ. It also does not show the console table in its real proportions, so it should not be used to judge design.
For most orders where the model is already settled, a door-size panel offers the best balance of cost, accuracy and confidence.
Format 3: The full mock-up
A full mock-up is a complete console table built to the project drawings, in the actual material, finish and hardware. It is the most complete of the custom furniture sample types, and also the most demanding in time and cost.
What a full mock-up proves
- The finish on every surface type: tops, edges, legs, drawer fronts, backs and inner faces.
- Proportion, dimensions and stability, checked against the shop drawings.
- Joinery quality, hardware operation and details such as cable cut-outs.
- How the piece looks in context, if you place it in a mock-up room or against the real wall colour and lighting.
Why it costs more
A mock-up uses real production labour, materials and often tooling, without the efficiency of a batch. Costs and timing depend on the complexity of the design, the materials and the finish system, so we quote them per project rather than giving a fixed figure.
Comparing the three formats
| Criteria | Stain card | Door-size panel | Full mock-up |
|---|---|---|---|
| Relative cost | Low | Moderate | Highest |
| Relative preparation time | Shortest | Short to moderate | Longest |
| Colour accuracy | Good for tone | Very good for tone and grain | Complete |
| Shows grain variation | Limited | Good | Best |
| Shows edges and shapes | No | Partly | Yes |
| Shows construction and proportion | No | No | Yes |
| Approval confidence | Low to moderate | High for finish | Highest overall |
Matching the format to your project
The right choice depends less on your budget alone and more on what could go wrong. Use these guidelines as a starting point.
Choose a stain card when
- You are still comparing colour directions or timber species.
- The order is small and the design is simple.
- You will follow with a larger sample before approval.
Choose a door-size panel when
- The model is fixed and you need to approve the finish for production.
- Grain, sheen and edge appearance matter to the designer or operator.
- You are ordering a batch where colour must stay consistent from piece to piece.
Choose a full mock-up when
- The console has curves, fluting, carving, inlay or mixed materials such as stone tops or metal parts.
- The order is large, or the piece is a signature element of the lobby.
- Several parties, such as the owner, brand and designer, must approve the same piece.
A staged approach that saves money
Many buyers combine formats rather than choosing only one. A typical sequence starts with stain cards to narrow the options, moves to a door-size panel in the chosen finish, and uses a full mock-up only when the design justifies it. This keeps the early, low-cost steps broad and spends on the expensive step only once.
For repeat or multi-room projects, it is also worth keeping the approved panel as a reference. A signed panel kept by both sides gives you a physical standard to compare against production pieces and later reorders.
Practical tips for any sample type
- Specify the substrate. A finish on solid oak looks different from the same finish on oak veneer or MDF, so the sample must use the production material.
- Check under your real lighting. Daylight and warm hotel lighting can change how a wood colour reads, so view the sample in the intended space where possible.
- Ask for more than one panel. Two or three panels show the natural range you should expect in the batch.
- State the sheen. Matte, satin and gloss change the perceived colour, so record the level in the approval.
- Record the finish code. Label and photograph the approved sample, and note the finish system used.
- Accept natural variation. Wood is a natural material, so agree in advance on an acceptable range rather than expecting identical boards.
Shipping and reviewing samples from abroad
Because we produce to order and supply buyers worldwide, samples are usually reviewed remotely or shipped by courier. Photographs are useful for early discussion, but screens vary and should not replace a physical sample for final approval. For this reason, physical door-size panels are the most common format for overseas finish sign-off, while full mock-ups are reserved for projects where the piece itself needs proving.
Shipping time and sample cost depend on the destination, the size and the finish, so it is better to plan the sample step into your programme from the start rather than treating it as a quick formality.
Conclusion
Stain cards help you choose, door-size panels help you approve, and full mock-ups help you prove. Matching the sample format to the complexity and size of your order protects both your colour standard and your schedule. If you are planning console tables for a hotel, restaurant or residential project, send us your drawings or reference images and tell us your quantity and target finish. We will recommend the most suitable sample format and prepare a project quotation.
Sıkça Sorulan Sorular
Is a stain card enough to approve a finish for a hotel order?
Usually not. A stain card is useful for choosing a colour direction, but it is too small to show grain behaviour, edges or batch variation. For production approval, most buyers use a door-size panel, or a full mock-up when the design is complex or the order is large.
How big should a finish approval panel be?
There is no fixed rule, but a panel around 300 x 600 mm (12 x 24 in) or larger gives a realistic view of grain and sheen. The panel should use the same material and finish system as production, and ideally include an edge profile.
When is a full mock-up worth the extra cost?
A full mock-up makes sense for large orders, signature lobby pieces, or designs with curves, fluting, inlay or mixed materials. It checks finish, proportions and construction together, which can prevent costly corrections after production has started.
Can I approve a wood finish from photos alone?
Photos are helpful for early discussion, but screens and lighting change how colour appears. For final approval, we recommend a physical sample reviewed under the lighting of the intended space, with the approved sample labelled and kept as a reference.
Will production pieces match the approved sample exactly?
Wood is a natural material, so small variations in grain and tone are normal. Supplying more than one panel and agreeing an acceptable range before production helps you judge the batch fairly and keeps expectations clear on both sides.
Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.





