Consoles and Dressers

Console Table Product Data Sheet: What to Ask a Manufacturer to Provide Before Ordering

A console table product data sheet is the document that turns a design idea into something you can check, approve and compare. This guide lists the submittal documents a procurement manager should receive for each model before releasing an order.

A console table product data sheet is a short technical document that describes one model: its dimensions, materials, finish, hardware, weight and packing. If you are buying for a hotel, restaurant or residential development, you should receive one for every model before you approve an order. It gives you a single reference that procurement, design and site teams can check against the drawings, the sample and the delivered goods.

This guide explains what a good data sheet contains, which supporting submittal documents sit alongside it, and how to spot gaps. It is written for buyers ordering made-to-order wooden furniture from overseas, where a clear paper trail replaces a showroom visit.

Why a data sheet matters for custom hospitality furniture

With made-to-order pieces there is no catalogue page to fall back on. What is agreed on paper is what the factory builds, and what you later inspect on site. A data sheet reduces misunderstandings between the designer, the buyer, the factory and the installer.

It also makes quotations comparable. If two suppliers quote for the same model but describe the material differently, the price difference may come from the specification, not from the supplier. A written data sheet makes that visible.

In some tenders, a furniture submittal is formally required before the contractor can order. Even where it is not, asking for one is good practice and costs the factory very little time.

What a console table product data sheet should contain

Think of the data sheet as a one- or two-page summary per model. The following headings cover what most buyers need.

Identification

  • Model name and code: a unique reference used on drawings, samples, packing labels and invoices.
  • Project name and location: so the sheet is tied to your order.
  • Revision number and date: essential when details change during approval.
  • Intended location: for example lobby, corridor or guest room entry, since this can affect specification.

Dimensions and tolerances

  • Overall length, depth and height in millimetres, with inches in brackets if your team works in imperial, for example 1200 mm (47.2 in).
  • Top thickness, leg or base section sizes, and any overhang or setback.
  • Stated manufacturing tolerance, so you know what variation is normal on repeated pieces.
  • Clearance to the wall, skirting notches or back panel detail where relevant.

Materials

This is the core of the material specification document. Ask the factory to state each component separately rather than writing only "wood".

  • Timber species and form: solid wood, veneer on engineered board, or a combination.
  • Core board type and thickness for veneered parts.
  • Edge banding or edge treatment.
  • Top material if different from the frame, such as stone, glass or metal inlay.
  • Adhesives and any fire-retardant (FR) treatment, if required by your destination.

Finish

  • Finish type: oil, lacquer, wax or another protective coating.
  • Gloss level, such as matte or satin.
  • Colour reference: a stain code, RAL number or the physical sample number.
  • Number of coats or the coating system, in general terms.

Hardware and components

  • Drawer runners, hinges, locks and handles, with type and brand or equivalent grade.
  • Levelling feet, wall fixing brackets or anti-tip fixings.
  • Cable cut-outs, grommets or integrated lighting, with positions shown on the drawing.

Weight and packing data

  • Net weight per piece and, if relevant, the recommended load limit for the top.
  • Packed dimensions and gross weight per carton or crate.
  • Packing method, such as corner protectors, foam, stretch film and carton or crate.
  • Whether the piece ships assembled or knock-down, and any assembly required on site.

The wider furniture submittal package

A furniture submittal is more than the data sheet. It is the set of documents that lets the owner, designer and contractor approve a model before production. For a console table, the following items are normally worth requesting.

DocumentWhat it showsWhy you need it
Product data sheetDimensions, materials, finish, hardware, weightSingle reference for the model
Shop drawingsPlan, elevations, sections and joinery detailsConfirms construction and fit to the space
Finish sample or stain cardPhysical colour and sheenApproving colour on screen is unreliable
Material sampleVeneer, timber or top materialChecks grain, texture and variation
Hardware sheetRunners, hinges, locks and fixingsVerifies quality grade and compatibility
Packing specificationPacking method and packed sizesSupports freight planning and damage prevention
Care and maintenance notesCleaning and repair guidanceHelps housekeeping and handover

Not every project needs every item. A small order of ten pieces may be fine with a data sheet, one drawing and a finish sample. A large hotel batch usually benefits from the full set.

How to review a data sheet before you approve it

Receiving the document is only half the task. Check it against your own brief and drawings.

  1. Compare dimensions with the architect's drawing, especially niches, alcoves and corridor clearances.
  2. Check the material wording. Vague terms like "wood finish" or "MDF veneer look" should be replaced with specific descriptions.
  3. Match the finish reference to a physical sample you have seen under your own lighting.
  4. Confirm the revision. Make sure the data sheet, drawing and quotation all carry the same revision.
  5. Look for gaps. If weight, tolerance or hardware is missing, ask for it in writing.
  6. Ask about regulatory needs. If your destination requires fire performance or environmental declarations, ask what documents the factory can supply for the materials used.

Common gaps buyers find

Some data sheets look complete but leave out details that cause problems later. Watch for these:

  • No stated tolerance, which leads to disputes about small variations in a batch.
  • Finish described by name only, such as "natural oak", with no sample or code.
  • Hardware listed as "standard" without naming the type or grade.
  • Packed weights missing, which makes freight and lift planning guesswork.
  • No revision control, so nobody is sure which version was approved.

How this fits into ordering from overseas

When you order custom pieces from a factory in another country, documents do much of the work that a site visit would otherwise do. The usual sequence is brief, quotation, shop drawings, sample, data sheet approval, then production release. Keeping the data sheet in step with each of these stages means that the piece you approve is the piece that is built and shipped.

At Palmiye we produce hotel and hospitality furniture to project drawings in our own factory in Istanbul and ship worldwide. Because every project is made to order, we can prepare a data sheet for each model to match your drawings and sample, and update it if the design changes during approval. Timing and cost depend on the materials, quantities and approval process of your project, so we confirm them once we have reviewed your brief.

Next step

If you are planning a console table order, send us your drawings, reference photos or a short brief with quantities and destination. We will review them and come back with a proposed specification, the supporting documents for approval and options for packing and shipping.

Sıkça Sorulan Sorular

What is a console table product data sheet?

It is a short technical document describing one console table model. It lists dimensions, tolerances, materials, finish, hardware, weight and packing details. Buyers use it to approve the specification, compare quotations and later check delivered pieces against what was agreed.

Is a data sheet the same as a shop drawing?

No. A shop drawing shows the construction visually through plans, elevations and sections. A data sheet summarises the specification in written form, including materials, finish and packing. Most projects benefit from both, because each answers questions the other does not.

Do I need a data sheet for a small order?

Yes, though it can be brief. Even for a few pieces, a one-page data sheet with a drawing and finish sample prevents misunderstandings. Larger hotel batches usually justify a fuller submittal package with hardware sheets and packing specifications.

Should the data sheet include fire or environmental information?

If your destination or tender requires it, ask early. The data sheet can state the materials and any fire-retardant treatment used. Supporting declarations depend on the materials and the supplier, so request what is relevant to your market in writing.

What should I do if the delivered piece differs from the data sheet?

Compare it with the approved revision of the data sheet, drawing and sample, and document the difference with photos and measurements. Then contact the supplier promptly. Small variations within the stated tolerance are normal; anything outside it should be discussed and resolved.

Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.

Related products

All Console Table Models

Get a quote for Console Table Models

Share dimensions and quantities; we will prepare a quote for your project.