Console Table Sizes in Inches and Centimetres: Converting Specifications for International Projects
A practical guide to console table size conversion for designers in imperial markets who brief a metric factory. Learn how to convert, round and document dimensions so the delivered piece fits.
Console table size conversion looks simple until a 14 in depth becomes 36 cm on one drawing and 35.6 cm on another. For a single piece the difference is small, but across 120 corridor consoles it can decide whether a piece fits its niche. This guide shows how to convert inches to cm for furniture, where rounding is safe, and how to brief a metric factory clearly.
Why conversion errors happen in hotel projects
Many hotel projects mix markets. The designer may work in feet and inches, the architect in millimetres, and the factory in centimetres or millimetres. Each handoff is a chance for a number to be rounded, retyped or misread.
Most errors come from a few habits:
- Converting once in a spreadsheet and again by hand on the drawing.
- Rounding every dimension to the nearest whole centimetre without checking the total.
- Writing fractions such as 31 1/2 in without a clear separator, so they are read as 311/2.
- Mixing nominal sizes (a "36 in console") with real measured sizes.
The basic conversion rules
One inch equals exactly 25.4 mm. That is a fixed definition, so you can always convert without approximation. Multiply inches by 25.4 to get millimetres, then divide by 10 for centimetres.
Feet are 12 inches, so 1 ft equals 304.8 mm. When a dimension is given as 2 ft 6 in, convert the full value to inches first (30 in) and then to millimetres (762 mm).
Quick reference for common sizes
| Inches | Millimetres | Centimetres |
|---|---|---|
| 10 in | 254 mm | 25.4 cm |
| 12 in | 304.8 mm | 30.5 cm |
| 14 in | 355.6 mm | 35.6 cm |
| 16 in | 406.4 mm | 40.6 cm |
| 30 in | 762 mm | 76.2 cm |
| 32 in | 812.8 mm | 81.3 cm |
| 36 in | 914.4 mm | 91.4 cm |
| 48 in | 1,219.2 mm | 121.9 cm |
| 60 in | 1,524 mm | 152.4 cm |
These values are mathematical conversions, not recommended sizes. Choose your dimensions from the room, then convert.
Work in millimetres, not centimetres
Centimetres hide precision. A value of 35.6 cm feels like a decimal, while 356 mm reads as a whole number and is how most workshops and CNC machines think. We suggest putting millimetres on every production drawing, with inches in brackets for your own team.
For example: 356 mm (14 in) depth. The factory builds to the millimetre figure, and your team can still check against the original imperial brief.
Decide which unit is the master
Every project needs one source of truth. If the design was drawn in inches, say so, and state whether the metric figures are converted values or the new master. Both approaches work, but they must not be mixed.
- Imperial master: the factory converts exactly and reports the millimetre value. Rounding is only allowed where you approve it.
- Metric master: you accept a rounded metric size, such as 350 mm instead of 355.6 mm, and the drawing is reissued with the new figure.
The second option often suits production well, because rounded sizes simplify panel cutting and jigs. It is worth asking the factory whether a small adjustment brings practical benefits. Approve it in writing before production.
Rounding rules that protect the fit
Rounding is not wrong, but it should be intentional. Consider where the piece will sit.
Pieces that fit into a space
If a console goes into a niche, alcove or between two fixed elements, round down on the width and note the clearance you expect. A piece that is 1 mm too wide cannot be installed; one that is 2 mm narrow can be hidden with a shadow gap.
Free-standing pieces
For free-standing consoles against a wall, rounding to the nearest 5 mm is usually acceptable visually. Height needs more care, because it relates to adjacent items such as mirrors, sockets and lamps.
Matching sets
When a console pairs with a mirror or a second table, convert both from the same source and round with the same rule. Otherwise the proportions drift by a few millimetres and the set looks off.
Standard console dimensions and how to read them
You will see "standard console dimensions" quoted in catalogues, but these are market habits rather than rules. Many consoles are shallow compared to their length, and the exact numbers vary by style and use. In hotels, corridor regulations, wall fixtures and door swings often set the real limit.
Instead of relying on a nominal figure, specify the three key dimensions yourself:
- Length (width along the wall).
- Depth (projection from the wall).
- Height (finished floor to top surface).
For more on typical ranges by space, our Console Table Dimensions Guide covers hotels, restaurants and residences. Here we focus on getting the numbers across the language of units without loss.
Fractions, decimals and typing habits
Imperial drawings often use fractions. Metric drawings use decimals. Translating between them is where typos appear.
- Convert fractions to decimal inches (31 1/2 in becomes 31.5 in).
- Multiply by 25.4 to get millimetres (800.1 mm).
- Decide on the rounding (800 mm) and mark it as approved.
- Record both values on the drawing.
Avoid writing sizes as 31-1/2" in an email body, as some systems strip the symbols. Writing "31.5 in" is safer and clearer.
Include tolerances in the brief
Wood moves with humidity, and finishing adds a thin layer to every surface. A factory cannot produce exactly 800.1 mm in a way you can measure on site. Agree on a tolerance, for example plus or minus a few millimetres on overall dimensions, and state it on the drawing.
Tighter tolerances may be possible where a piece must fit a niche, but they affect process and cost, so discuss them before approval. Our article on Console Table Delivery Tolerances and Fit goes deeper into measuring for alcoves and skirting boards.
A conversion checklist for your brief
Use this list before sending drawings to a metric factory:
- State the master unit and whether the conversions are rounded.
- Give all dimensions in millimetres, with inches in brackets.
- Mark which dimensions are critical (niche width, height to mirror, depth in corridors).
- Show overall size and component sizes, such as top thickness and leg section.
- Agree on tolerance and where it applies.
- Confirm that the top thickness and edge profile are converted from the same source.
- Ask the factory to reissue the drawing in your preferred units for sign-off.
Sign-off through drawings and samples
Even with perfect conversion, the safest step is to approve a shop drawing that shows both unit systems. Compare each figure against your original. If the project is large, a sample or mock-up lets you check the real piece against the wall, mirror and neighbouring joinery.
When a reorder happens years later, the approved drawing becomes the reference. Keep the version with both units and the rounding notes, so future orders match the first batch.
Summary
Console table size conversion is straightforward if you use the exact 25.4 factor, work in millimetres, name a master unit, and approve rounding deliberately. Put both systems on the drawing and mark critical dimensions clearly.
If you are preparing a hotel or hospitality project and have sizes in inches, send us your drawings or sketches. We will convert them, flag anything that needs rounding and return a shop drawing for your approval before production, with worldwide shipping options for your destination.
Sıkça Sorulan Sorular
How do I convert inches to cm for furniture?
Multiply the inch value by 2.54 to get centimetres, or by 25.4 for millimetres. The factor is exact, so no approximation is needed. For feet and inches, first convert everything to inches. For production, millimetres are preferable because they avoid decimals and match workshop practice.
Should I send my drawings to the factory in inches or centimetres?
Send them in your working unit, but add millimetre values in brackets or ask the factory to do so. What matters is that one unit is the master and both appear on the approved drawing. This keeps your team and the workshop looking at the same numbers.
Is it safe to round converted dimensions?
Yes, if it is deliberate. Round down on dimensions that must fit into niches, and round to the nearest 5 mm on free-standing pieces if the design allows. Always note the rounded figure on the drawing and approve it in writing before production starts.
What tolerance should I expect on a custom console table?
Tolerance depends on the material, construction and finish, so it should be agreed per project. Wood reacts to humidity, which makes zero deviation unrealistic. State a tolerance on the drawing and mark any critical dimensions so the factory can check them during production.
Are there standard console dimensions I can use for orders?
There are common ranges, but no universal standard, especially in hospitality. Corridor widths, wall fixtures and design style all influence the right size. It is better to specify length, depth and height from your own plans, then convert them carefully for the factory.
Can the factory convert my imperial drawings for me?
Yes. Send your drawings or sketches and we will convert them to millimetres, flag any rounding that might help production, and issue a shop drawing in both units for your approval before manufacturing begins.
Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.





