Consoles and Dressers

Sound Bars, Consoles and Game Devices: Planning Equipment Space in a TV Unit

Start with an equipment list, not a cabinet sketch. This guide shows how to turn sound bars, consoles and boxes into opening sizes, shelf depths and clearances for custom and bulk TV unit orders.

A TV unit for a sound bar, a game console and a set-top box only works if the openings are sized around the real devices. The most reliable method is simple: list every piece of equipment first, measure it, and only then fix the cabinet dimensions. This guide explains how to do that for custom and wholesale orders, whether you are furnishing hotel suites, residential units or a retail range.

Why the equipment list comes before the cabinet drawing

Many TV units are drawn from a visual concept and the equipment is squeezed in afterwards. The result is a console that does not fit its shelf, a sound bar that blocks the screen or cables that have no route. Reversing the order avoids most of these problems.

For an international order, the list also gives the factory a clear brief. Instead of guessing, we can propose opening sizes, shelf depths and cut-outs that match what will actually be placed inside.

Step 1: Build the equipment schedule

Write down every device that will sit in or on the unit. For each one, record the following:

  • Width, depth and height in millimetres (and inches if your team works in imperial).
  • Weight, especially for AV receivers and larger consoles.
  • Connection points: power, HDMI, optical, network, and which side they are on.
  • Ventilation needs: whether the device vents from the top, sides or rear.
  • Remote control type: infrared devices need a clear line to the front, while radio-based ones do not.

If the project uses several models, list the largest realistic size of each device type, not the average. A cabinet that fits the biggest model will also fit the smaller ones.

Step 2: Plan the sound bar position

A sound bar is usually 60 to 120 cm (24 to 47 in) wide or more, depending on the model, so always check the exact product. There are three common ways to place it in a TV unit.

On the top surface, in front of the screen

This is the simplest layout. Check that the bar does not cover the lower edge of the screen or the TV's infrared sensor. Leave a small gap between the bar and the screen frame, and confirm the TV's own feet or stand height.

On a shelf below the screen

An open shelf directly under the TV suits sound bars that need clear sound projection. Do not place a sound bar behind a solid door or a closed front. A slatted or acoustically transparent front panel is possible, but it should be approved on a sample first.

Wall-mounted under or above the screen

Some sound bars come with a wall bracket. If the TV unit includes a back panel or media wall, the bracket position and the fixing reinforcement must be drawn in advance, because it is difficult to add later.

Step 3: Size shelves for consoles and boxes

For a TV stand with a game console, depth and airflow matter more than width. Consoles are often wider than they look in photos, and some are designed to stand upright, which changes the opening height.

  • Opening height: add clearance above the device so warm air can leave. Even a few centimetres make a difference.
  • Opening depth: allow for the device plus the space behind it for plug and cable bends. HDMI and power plugs are not flat.
  • Controller storage: a small drawer or side compartment keeps controllers, remotes and charging cables tidy.
  • Disc-based devices: keep the front of the opening free so trays can open fully.

For the full picture on heat, see our article on TV unit ventilation and heat, which covers open backs, vent slots and fan options in more detail.

Step 4: Use a planning table

The table below shows a practical way to turn the equipment list into cabinet requirements. The values are planning prompts, not fixed standards; always confirm them against the real device data sheets.

EquipmentWhat to checkCabinet implication
Sound barLength, height, speaker directionOpen front or acoustic panel; avoid blocking the screen
Subwoofer (if separate)Size, wireless or wiredFloor space or side compartment with ventilation
Game consoleFootprint, orientation, ventsOpening with generous top and rear clearance
Set-top box or streamerSmall size, remote typeShallow shelf; infrared access to the front
AV receiverWeight, heat, many cablesReinforced shelf, extra depth, open back
Router or hubAntenna, power adapterSeparate small compartment or service access

Step 5: Plan power and cables with the same list

Every device on your schedule needs power and often a signal cable. Count the sockets, add a margin for adapters and decide whether the power strip will sit inside the unit or be fixed to the wall. Cut-outs in shelves and back panels should be placed where the cables really leave the devices, not just in the centre.

Leave a service route as well. If a console fails or a cable is replaced, staff or the owner should be able to reach the connections without removing the whole unit. Our guide on cable management covers concealed routing and service access in detail.

Step 6: Check the load on shelves

Heavier devices such as AV receivers need a shelf that will not sag. Long spans, thin boards and heavy loads are a poor combination. A vertical divider, a thicker board or a reinforcing rail under the shelf solves most cases. Give the factory the weight of the heaviest device so the shelf thickness can be decided with the span in mind.

What changes for hotel and bulk projects

In hotels, serviced apartments and residential developments, the equipment is usually fixed by the operator, which makes planning easier. You can standardise one equipment list and apply it to every room. Two points deserve extra attention.

  • Locked or hidden devices: if streaming boxes or casting devices must be inaccessible to guests, plan a lockable compartment or a concealed bracket behind the screen.
  • Replacement cycle: devices change every few years. Leave a little extra space in each opening so that a newer model, which may be larger, still fits.

For wholesale orders sold under your own range, you may prefer two or three cabinet variants: one with an open shelf for a sound bar, one with a closed console compartment, and one compact version. This keeps production efficient while covering most buyer needs.

Information to send with your request

To receive an accurate proposal for a custom TV unit, prepare the following:

  1. The equipment schedule with dimensions and weights.
  2. The screen size and mounting method (wall, stand or on the unit).
  3. The room or wall dimensions and the position of sockets.
  4. Reference photos or a sketch of the style you want.
  5. Quantities, delivery country and preferred shipping terms such as FOB or DAP.

Palmiye produces custom cabinetry in our own factory in Istanbul and ships worldwide, so we can work from your drawings or help develop them. For larger programmes, we usually recommend approving one sample before bulk production, so opening sizes and clearances can be tested with the real devices.

Common mistakes to avoid

  • Designing openings from catalogue photos instead of measured devices.
  • Placing the sound bar behind a closed door or solid panel.
  • Ignoring plug depth and cable bend radius behind devices.
  • Forgetting a remote-control path for infrared equipment.
  • Sizing shelves for today's console only, with no allowance for newer models.

Next step

If you are planning a TV unit with a sound bar, console or other equipment, send us your equipment list and drawings. We will review the openings, shelf depths and ventilation and come back with suggestions, an estimated lead time and shipping options for your project.

Sıkça Sorulan Sorular

How deep should a TV unit be for a sound bar and console?

Most sound bars need little depth, but consoles and receivers need space for ventilation and plugs. Measure the deepest device, then add clearance behind it for cables. The exact figure depends on your equipment, so confirm it with the device data sheets before fixing the drawing.

Can a sound bar sit behind a cabinet door?

Usually not. Solid doors block and muffle the sound. If you want a closed look, use an open shelf or an acoustically transparent front such as a slatted or fabric-faced panel, and approve it on a sample before production.

How do I stop a game console overheating in a TV unit?

Leave open space above and around the device, and avoid sealed compartments. Back panel cut-outs or vent slots help warm air escape. Check the console manufacturer's guidance and tell the factory the exact model so the opening can be sized accordingly.

What information does a factory need to size equipment openings?

Send the equipment list with width, depth, height and weight, plus connection positions and the screen size. Add wall dimensions, socket locations and reference photos. With this, a factory can propose opening sizes, shelf thickness and cut-outs more accurately.

Can Palmiye make TV units for bulk or hotel orders with equipment compartments?

Yes. We produce custom cabinetry to project drawings and can include compartments for sound bars, boxes and consoles, including lockable options. Quantities, finishes and shipping terms are agreed per project, and a sample is often recommended before bulk production.

Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.

Related products

All Console Table Models

Get a quote for Console Table Models

Share dimensions and quantities; we will prepare a quote for your project.